Mastering Basic Plumbing When You Install a Bathtub

Call Today

This great article down below about A Step-by-Step Guide to Installing a Bathtub is really stimulating. Don't skip it.


Tools You Need to Install a New Bathtub
Installing a bath tub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably tough task. If the old tub is conveniently available, the task can move quickly; if you need to open a wall to remove the old bathtub and also position the new tub, the job is much harder. In either instance, the project is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and set in the new one. Ensure you have actually certified yourself for the task as well as are comfortable attempting it. Instead of hiring a specialist to take control of a halfway-completed job, it is better to consider employing one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This write-up will certainly help you install a brand-new bathtub in your bathroom if you have actually already acquired a new bathtub as well as do not need to transform the plan of your previous water supply pipelines.
Your devices and also product list should comprise the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you need to replace old faucets with new ones as a part of your installment, then the first thing you need to do is disconnect the water. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing taps can be quite problematic due to the limited accessibility that is often the case.
    Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a towel all set for the staying water that will originate from the pipes. When the supply pipes have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
    Before going on to fit the new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.

    Suitable New Touches


    If the tails of the new faucets are plastic, then you will need a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end supplies a link to the existing supply pipes.
    If you need to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
    Next, position the faucet in the installing hole in the bath/basin guaranteeing that the washing machines remain in location in between the faucet and also the sink. Protect the faucet in position with the manufacturer given backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former kind ought to be connected to the faucet finishes first, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been linked.

    Mounting the Bathtub


    Using both wood boards under its feet, put the tub in the required setting. The wooden boards are helpful in evenly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 little factors.
    The next goal is to make certain that the bathtub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the bathtub up until the level reviews level.
    To set up faucets, fit the bottom of the furthest flexible tap adapter to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
    Activate the water system and also examine all joints and also new pipework for leaks and tighten them if necessary. Fill the bath tub as well as likewise inspect the overflow outlet and also the typical outlet for leakages.
    Finally, fix the bathroom paneling as described in the manufacturer's instruction manual. Tiling and securing around the bath tub should wait till the bath tub has been made use of at least when as this will certainly settle it into its final position.

    Planning for the Installation


    Firstly, the supporting framework provided with the bathroom ought to be fitted (if needed) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to stop strain on the tub.
    Fit the flexible faucet connectors to the bottom of the two taps using 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you make use of every one of the supplied washers.
    Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must now prepare to be suited its last placement.

    Tiling Around the Bathtub


    In the location where the bathroom meets the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to fracture a rigid seal, triggering the water to pass through the wall surface between the bathroom and the tiling, resulting in problems with dampness and feasible leakages to the ceiling listed below.
    You can pick from a selection of coloured sealers to assimilate your components as well as fittings. They are marketed in tubes and also cartridges, as well as can sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of drenched newspaper or soft rope. Remember to constantly load the bath tub with water prior to securing, to enable the motion experienced when the tub remains in usage. The sealer can break fairly very early if you do not take into account this activity prior to sealing.
    Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently readily available on the marketplace. It is suggested to fit the ceramic tiles making use of waterproof or waterproof sticky as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    Do you really like more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Make feedback below. We'd be pleased to listen to your opinions about this blog entry. We are looking forward to see you back again in the near future. Sharing is good. Helping people is fun. Thanks a lot for your time. Please visit our blog back soon.


    One-stop solution, phone now!

    Leave a Reply

    Your email address will not be published. Required fields are marked *